For Industrial & Commercial Sites

Industrial Roof Condition Inspection

You have eight thousand square metres of roof. This tells you where the defects on it are — each one numbered, photographed and given a grid reference you can hand to a contractor — without putting anyone on the roof.

What you receive

The roof map

One straight down Ortho image of the roof.

  • Built from overlapping frames flown to a fixed grid
  • A lettered and numbered grid printed over it
  • Your building’s own column grid used where drawings exist
  • The grid key published on the page, so a reference means something

The defect register

Every visible defect, numbered and located.

  • What it is, by category
  • Where it is, by grid reference
  • A close photograph of that specific item
  • Numbered in a stable order, so a later inspection can be compared

The detail frames

The evidence behind each entry.

  • Shot on a telephoto lens from a stand-off distance
  • Laps, ridges, gutters, flashings and penetrations
  • Close enough to resolve a fastener head and its washer
  • Supplied at full resolution alongside the report

A defect with no address is worthless. “Corrosion somewhere on the north side” cannot be quoted against and cannot be actioned. Everything in the register has a grid reference and a photograph attached to it.

What we look for

Corrosion at side and end laps

Where sheets overlap and water sits longest.

Fastener condition

Rust bloom around heads; failed, backed-out or missing washers.

Sheet edges

Lifting and fretting along edges and at the ridge.

Sealant

Cracked, debonded or missing at laps and details.

Translucent sheeting

Yellowing, crazing and cracking — usually the oldest failure on the roof.

Gutters and valleys

Visible blockage, debris load and standing water.

Ponding

Where a shallow pitch is not draining.

Hail damage

Denting across the field of the roof.

Flashings and penetrations

Around vents, extractors, skylights and services.

Previous repairs

Patches, over-sheeting and coatings, and how they are holding.

We record and locate the defects. We don’t rate the roof, estimate what is left in it or specify the repair — that is your contractor’s call, and the register is written to be handed straight to him. Gutter interiors, sheet undersides and anything concealed cannot be seen from above, and we say so on site before we fly.

By the time it leaks, you are not paying for a roof repair

A sheeted roof almost never fails suddenly. Corrosion creeps along a lap, a row of fastener washers perishes, sealant lets go at a flashing — and none of it is visible from the factory floor. The first anyone knows is water on the floor, and by then it has been going on for two or three seasons.

At that point the cost is no longer the roof. It is the stock under the leak, the plant it lands on, the production stopped while somebody deals with it, and a repair that has grown from a dozen fasteners into a bay of sheeting.

It is not neglect — it is access. Putting a man on that roof means fall protection, a safety file and usually a machine to get him up there, and when it is done he has seen the part he walked on.Flown, the whole roof is covered in about an hour on site, at a resolution that shows an individual fastener, while the plant carries on running.

Where thermal fits, and where it does not

On a bare corrugated or IBR steel roof — which is most of the Gauteng industrial belt — a thermal camera adds very little. Bare metal is reflective, and there is no insulation core beneath it to hold water and show up as heat. We do not sell it there.

It earns its place on three kinds of roof: insulated sandwich panel and cold stores, where there genuinely is a core; membrane and built-up flat roofs, where we supply the thermal capture itself for someone qualified to interpret; and tracing an active leak after rain, where you already know water is coming in and want the entry point narrowed down. It is an add-on to the visual inspection, never a replacement for it.

Before a solar installation

If an array is going onto the roof, the condition of that roof on the day before installation is worth recording — by both parties. It means the installer cannot be charged for damage that was already there, and the building owner cannot later be told that new damage was pre-existing.

The same visit after commissioning covers every penetration, bracket, rail foot and flashing the installation added. One roof dispute on a multi-million-rand install costs considerably more than the record does.

Where we fly

The industrial areas of the West Rand and greater Johannesburg, and across the belt surrounding Johannesburg and Pretoria — Gauteng, North West, Free State and Mpumalanga. The towns are listed on theservice area page.

Flown legally

All flight operations comply with SACAA Part 101, including licensed pilot operation and appropriate airspace clearance for every site.

On an industrial stand this is a practical matter, not a formality. The regulations set minimum distances from people, from buildings belonging to somebody else, and from public roads — and industrial parks are tight. We check the site against those distances before quoting, rather than discovering the problem on the morning of the flight.

Not sure the roof warrants it? That is usually the point — nobody has seen it recently enough to know. Ask, and we will tell you plainly whether your site is a sensible one to fly.

Ask about your roof